Publikationer / Publications
- Thuvander, A.
Prediction of the galling tendency in sheet metal forming applications with
nitrogen-alloyed tool steel, 8th INTERNATIONAL TOOLING CONFERENCE, 2-4 June
2009, Aachen, Germany
- Sandberg, O., Högman, B., Johansson, B. and Thuvander,
A.
New tool concept for stamping of HSS and AHSS sheet, Conference of IDDRG,
Best in Class Stamping, 16-18 June 2008, Olofström,
Sweden, pp. 591-602
- Thuvander, A. and
Sandberg, O., Computation of die loads in sheet forming using dies
of tool steel with improved anti-galling properties, International
Symposium on Friction, Wear and Wear Protection, 9-11 April 2008, Aachen,
Germany
- Thuvander, A.
Computation of gear distortion from case hardening with low pressure
carburising, 1st INTERNATIONAL CONFERENCE ON DISTORTION ENGINEERING, 14-16
September 2005, Bremen, Germany
- Thuvander, A.
Numerical simulation of gas quenching of tool steels and the influence of
hardenability on distortion, 6th INTERNATIONAL TOOLING CONFERENCE, 10-13
September 2002, Karlstad, Sweden
- Thuvander, A.
Out of roundness distortion of bearing rings owing to internal stresses
from tube bending, Materials Science and Technology, vol. 18, no. 3, pp.
312-318, March 2002
- Volkmuth, J., Sjöblom, U., Slycke, J. and Thuvander, A.
Effect of Uneven Residual Stresses on Dimensional Changes and Variations
of Through Hardening Bearing Steel Rings, 20th ASM Heat Treating Society
Conference, 9-12 October 2000, St. Louis, MO, USA
- Thuvander, A.
Prediction of heat treatment distortion using numerical simulation, PhD
thesis, Report KTH / AMT-198, (2000)
- Schmauder, S., Melander, A., McHugh, P. E., Rohde, J., Hönle, S., Mentchev, O., Thuvander, A., Thoors, H.,
Quinn, D. and Connolly., P.
New tool materials with a structural gradient for milling applications, J.
Phys. IV France 9 (1999), 147-156
- Thuvander, A.
and Germidis A.
Numerical Prediction of Heat Treatment Distortion of High Speed Steels -
Importance of pro-eutectoid carbides, Proc. 3rd Int. Conf. on Quenching
and the Control of Distortion, Prague, Czech republic, (1999), 311-321
- Thuvander, A., Melander, A., Lind, M., Lior,
N. and Bark, F.
Prediction of Convective Heat Transfer Coefficients and their Effects on
Distortion of Cylindrical Steel Bodies Quenched by Gas Cooling, 5th
ASME/JSME Joint Thermal Engineering Conference, San Diego, California,
USA, March
1999
- Thuvander, A., Melander, A., Lind, M., Lior,
N. and Bark, F.
Prediction of Convective Heat Transfer Coefficients and Examination of
their Effects on Distortion of Cylindrical Tubes Quenched by Gas Cooling,
La Metallurgia Italiana,
Vol. XCI, 4, pp.
25-32, April 1999.
- Thuvander, A., Melander, A., Lind, M., Lior,
N. and Bark, F.
Prediction of Convective Heat Transfer Coefficients and Examination of
their Effects on Distortion of Cylindrical Tubes Quenched by Gas Cooling,
4th ASM Heat Treatment and Surface Engineering Conference, Florence,
Italy, Oct. 1998
- Chandrasekaran, H.
and Thuvander, A.
Modeling tool stresses and temperature
evaluation in turning using finite element method, Machining Science and
Technology (USA), vol. 2, no. 2, Dec. 1998, 355-367
- Thuvander, A., Blom, R., Lai-Zhe Jin and Sandström, R.
Material property database for heat treatment simulation of tool
materials., Steel Research, 68 (1997), 125-131
- Thuvander, A., Höglund, L., Melander, A.,
From, A., Jonsson, S., Ågren,
J., Ölund, P., Andersson,
J.-E., Lund, T, Beswick, J. and Slycke, J.
Simulation of heat treatment response of bearing steels, 5th Int. Symp. on Bearing Steels: Into the 21th century, New
Orleans, USA, Nov. 1996
- Thuvander, A.
Calculation of distortion of tool steel dies during hardening, Proc. 2nd
Int. Conf. on Quenching and the Control of Distortion, Cleveland, USA,
(1996), 297-304
- Schedin, E., Thuvander, A., Henderson, P., Sandberg, P. and Kamf, A.
Stress relaxation behaviour of connectors - development of simulation
techniques, Presented at the IEEE Holm Conference on Electrical Contacts,
Chicago, USA, Sept 1996
- Linder, J., Bergengren,
Y., Thuvander, A., Melander,
A. and Gustavsson, A.
Fatigue of spot welded stainless sheet steels, Fatigue '96: Sixth International
Fatigue Congress. Vol. II, Berlin, Germany, 6-10 May 1996
- Thuvander, A.
Numerical simulation of distortion due to heat treatment, Licentiate
thesis, Report KTH / AMT-143 (1995)
- Thuvander,
A and Melander, A.
Prediction of distortion and residual stresses of engineering steels due
to heat treatment, Second ASM Heat Treatment and Surface Engineering
Conference, Dortmund, Germany, June 1993, Vol. 2, 641-656
- Thuvander,
A and Kamf, A.
Computer calculation of stress relaxation in a model connector - simulation
of different materials, Multiplex Technology Application in Vehicle
Electrical Systems (SP-954), International Congress and Exposition,
Detroit, Michigan, SAE, (1993)
- Jansson, B, Rolfson, M, Thuvander, A, Melander, A, Wullimann, C.
Calculation of Microstructure and Hardness of Hot Tolled Steel Bars,
Materials Science and Technology, vol. 7, no. 2, pp. 118-127, Feb. 1991
- Thuvander, A and
Melander, A.
Calculation of distortion during quenching of a low carbon steel, First
ASM Heat Treatment and Surface Engineering Conference, Amsterdam,
Netherlands, (1991), Vol 2, 767-782
- Thuvander, A., Melander, A. and Jansson, B.
Calculation of distortion of steel components during quenching, The 7th
International Congress for the Heat of Materials, Moscow, USSR, (1990), Vol V, 27-33
- Schedin, E.
and Thuvander, A.
Surface asperity deformation during sheet forming, Third International
Conference on Technology of Plasticity (3rd I.C.T.P), July 1990, Kyoto,
Japan.
- Schedin, E.
and Thuvander, A.
Friction mechanisms during sheet forming, The 16th biennial congress of
IDDRG, June 1990, Borlänge, Sweden.
- Kamf, A., Sundberg, R., Karlsson, S.
and Thuvander, A.
Formability and solderability of tin and
tin/lead coatings on brass strips, Metall, 44/9
(1990), 835-839
- Chandrasekaran, H., Thuvander, A. and Wisell, H.
Modelling of stresses in peripheral milling, Annals of the CIRP Vol. 37/1
(1988), 41-44
- Melander, A.
and Thuvander, A.
A finite element study of a cold forging test, Scand. J. Metallurgy 17
(1988), 73-83
- Schedin, E.
and Thuvander, A.
Influence of sheet thickness, tool dimensions, and grain size on the
formability of brass sheet., Paper presented at the IDDRG-WG conference in
Switzerland, May 1987
- Thuvander, A.
Strain distribution in a pressed component of brass sheet, Scand. J.
Metallurgy 15 (1986), 170-184
- Thuvander, A., Melander, A. and Hutchinson, W. B.
Processing of phosphorus-alloyed low-carbon steel sheet by continuous
annealing., Metals Technology 11 (1984), 105-114
- Melander, A.
and Thuvander, A.
Influence of surface roughness and void growth at inclusions on the
forming limit diagram of brass., Scand. J. Metallurgy 12 (1983), 217-226
- Melander, A.
and Thuvander, A.
Criteria for breaks during wire drawing, Developments in the Drawing of
Metals, London, May 11-13 1983
Tillbaka till
början
Åter till startsidan